Skip to main content

A service of Otto Zickwolff GmbH, Germany

Dimension tables & drawingsVisit our shop →

Standards guide · Stainless steel reducers

Stainless steel reducer: dimensions and dimensional drawing to EN 10253-4

EN 10253-4D 21.3–406.4 mmconcentric and eccentricDimensions in mmfrom stock or to order

Standard
EN 10253-4:2025-10
Material
stainless steel
Designs
concentric / eccentric
Dimension
L

Dimensional drawing for your size

Design

EN 10253-4 covers the greyed-out sizes. Our dimension overview lists them as order dimensions – see the table “Further deliverable dimensions” below.

Stainless steel reducer · concentric · 219.1 × 2.9 – 168.3 × 2.6 mm

Stainless steel reducer EN 10253-4 in 3D – rotatable, all sizes 21.3 to 323.9 mm

Stainless steel reducer EN 10253-4, concentric 219.1 × 168.3 mm – 3D view
Typical design as a 3D view: Stainless steel reducer EN 10253-4, concentric 219.1 × 168.3 mm. Own illustration based on the dimensions on this page.
Dimensional drawing of a reducer in stainless steel, concentric, 219.1 × 2.9 – 168.3 × 2.6 mm 219.1 (D) 168.3 (D1) 152 (L) 2.9 (T) 2.6 (T1) © zickwolff.de large end small end Stainless steel reducer · concentric · 219.1 × 2.9 – 168.3 × 2.6 mm DIN EN 10253-4:2025-10 · Data as of 2026-08-25 · all dimensions in mm · to scale L is the overall length across both welding ends the transition is drawn as a cone with short cylindrical end sections – the standard dimensions D, D1, T, T1 and L, not the shape in between the two circles are the view onto the welding ends, at the scale of the drawing above – the large end on the left, the small one on the right · drawing calculated from the dimensions of the standard · Otto Zickwolff GmbH · zickwolff.de/wissen
Reducer in stainless steel, concentric, 219.1 × 2.9 – 168.3 × 2.6 mm: section in the axial plane with the overall length L, below it the view onto both welding ends. The transition is drawn as a cone with short cylindrical end sections, the standard dimensions D, D1, T, T1 and L, not the shape in between.
How to use the dimensional drawing – with example and direct link

Select design, large end, small end and wall thickness – the drawing and the dimension table then show exactly that size, with the figures in the drawing itself instead of only the dimension letters. What separates the concentric from the eccentric design, and type A from type B is on the reducer basics page. The dimension tables for the size pairs listed here are further down this page.

How it works: Choose 219.1 mm in the field “Outside diameter”, 168.3 mm in the field “Small end” and Series T2.9-2.6 in the field “Wall thickness”. The dimensional drawing immediately shows every dimension of the stainless steel reducer with tolerances, the table below all sizes. “Print this size as PDF” takes the drawing with you.

Example concentric, 219.1 × 2.9 – 168.3 × 2.6 mm: outside diameter (large end) D 219.1 mm, wall thickness (large end) T 2.9 mm, inside diameter (large end) 213.3 mm, outside diameter (small end) D1 168.3 mm, wall thickness (small end) T1 2.6 mm, inside diameter (small end) 163.1 mm.

Direct link to this size: https://www.zickwolff.de/wissen/en/reducers-stainless/?d=219.1&d1=168.3&reihe=T2,9-2,6

Technical basis: DIN EN 10253-4:2025-10. Zickwolff has prepared this presentation for practical use, with our own structure, our own designations and a statement of what kind of value each figure is. The original standard governs normative requirements.

Dimensions of the reducer in stainless steel, concentric, 219.1 × 2.9 – 168.3 × 2.6 mm
PropertyValueType of information
basic data
Wall thickness seriesSeries T2.9-2.6standard dimension
Availabilityfrom stock or to ordertrade information
nominal size (large end)DN 200assignment
nominal size (small end)DN 150assignment
connecting dimensions The dimensions at the welding ends that govern the joint with the pipe that follows.
outside diameter (large end) D219.1 mmstandard dimension
wall thickness (large end) T2.9 mmstandard dimension
inside diameter (large end)213.3 mmcalculated
outside diameter (small end) D1168.3 mmstandard dimension
wall thickness (small end) T12.6 mmstandard dimension
inside diameter (small end)163.1 mmcalculated
installation dimensions The dimensions that determine the installation space.
overall length L152 mmstandard dimension

Without an entry in the “Type of information” column: standard dimension. A dimension that EN 10253-4 specifies for this size.

Where exactly it is measured

outside diameter (large end) D
measured across the edge at the welding ends
outside diameter (small end) D1
measured across the edge at the welding ends
wall thickness (large end) T
measured at the welding end of the large end
wall thickness (small end) T1
measured at the welding end of the small end
inside diameter (large end)
ID = D − 2T
inside diameter (small end)
ID1 = D1 − 2T1
overall length L
overall length across both welding ends

Not in the dimensional drawing: ⌀ 57 – 26.9, ⌀ 57 – 33.7, ⌀ 57 – 42.4, ⌀ 57 – 48.3, ⌀ 108 – 48.3, ⌀ 108 – 60.3, ⌀ 108 – 76.1, ⌀ 108 – 88.9, ⌀ 133 – 60.3, ⌀ 133 – 76.1, ⌀ 133 – 88.9, ⌀ 133 – 114.3, ⌀ 159 – 76.1, ⌀ 159 – 88.9, ⌀ 159 – 114.3, ⌀ 159 – 139.7, ⌀ 559 – 355.6, ⌀ 559 – 406.4, ⌀ 559 – 457, ⌀ 559 – 508 – No dimension row arises for these combinations: for one of the two diameters the standard gives no wall thickness series – without a wall thickness there is neither a scale drawing nor a complete dimension row.

Dimensions are nominal dimensions to EN 10253-4 and do not replace the data sheet of the actual item. No statement about pressure or temperature suitability and no statement about the material. L is the overall length across both welding ends. The design makes no difference to the dimensions. Direct link to this size

Where it is measured – at the welding end

Measured at the welding end – D on the extended cylindrical outside surface, T as the full wall to the inside surface, as the standard enters both at the end plane – not at the root face.

inside of the pipeTDbevel 30° +5/−0root face C 1.6 ± 0.8 mm
Wall section at the welding end – not to scale. Image: Zickwolff
inside of the pipeTDbevel 30° +5/−0outside ≤ 30°inside ≤ 18°root face C 1.6 ± 0.8 mm
Machined end: chamfered outside up to 30° and inside up to 18° – the wall at the end may become thinner. T is dimensioned at the end plane from the end of the outer chamfer to the end of the inner chamfer, as in the standard figure. Not to scale. Image: Zickwolff

EN 10253-2 and EN 10253-4 measure outside diameter D and wall thickness T at the welding ends. In the standard’s figure both are entered at the end plane: D on the extended cylindrical outside surface, T as the full wall between the extended outside surface and the inside surface – the bevel only appears to cut the wall. The root face C of 1.6 ± 0.8 mm is not T. If the end is machined (chamfered outside up to 30° and inside up to 18°, which the standard expressly allows), T runs from the edge where the outer chamfer ends to the edge where the inner chamfer ends. On the body of an elbow the wall may be thinner – only the lower limit of table 12 applies there (type A), and no upper limit is defined for the body. The diameter on the body is limited only by out-of-roundness.

Typical measuring error: Measuring with the caliper across the bevel or the inside taper gives too small a wall – a conforming fitting is then wrongly rejected.

Rule of thumb: Measure the full wall – not the root face.

The standard names dimensions. What is listed here, we carry – from stock or to order; how quickly a size is available we clarify on request.

How to measure correctly

A reducer is identified by five measurements: outside diameter and wall thickness at the large end (D, T), the same at the small end (D1, T1), and the overall length L across both welding ends. Measure the diameters across the edge of the welding ends. Whether the part is concentric or eccentric is seen, not measured: on an eccentric reducer one side runs straight through.

outside diameter (large end) D
measured across the edge at the welding ends
outside diameter (small end) D1
measured across the edge at the welding ends
wall thickness (large end) T
measured at the welding end of the large end
wall thickness (small end) T1
measured at the welding end of the small end
overall length L
overall length across both welding ends

A measured value rarely matches the table exactly. The dimensional drawing on this page shows the limit deviations of EN 10253-4 for every size.

Design

Concentric and eccentric

On the concentric reducer both welding ends lie on a common centre line – the reduction runs evenly all round. On the eccentric reducer the two axes are offset parallel to each other: one generatrix runs straight through, and on that side the part stays flush with the line.

The standard lists both designs in one dimension table (Table A.9): large end D, small end D1, wall thicknesses T and T1 and the overall length L are identical – even the weight does not differ. That is why the design is, in the dimensional drawing above, a switch on the drawing and not a size selection of its own. Only the pressure factor depends on the design; the tables for it are given further down.

When which design is installed – straight generatrix at the top or at the bottom – is explained on the basics page on reducers.

Welded concentric stainless steel reducer 1.4571 to EN 10253-4
Concentric – stainless steel 1.4571, the reduction runs evenly all round.
Eccentric reducer with straight generatrix – design shown in carbon steel
Eccentric – one generatrix runs straight through (design, photo in carbon steel).

Where which design is installed is explained on the basics page.

Type A and type B

Type A and type B: the pressure factor

At the conical transition a reducer carries the internal pressure differently from the straight pipe. The standard describes this with two versions:

Version

Type A – reduced pressure factor

Wall thickness at the fitting body as at the welding ends. How much internal pressure the part carries compared with the straight pipe is stated by the pressure factor X in per cent – separately for both designs, in the tables below.

Version

Type B – full pressure resistance (standard: “for use at full service pressure”)

Increased wall thickness at the fitting body, designed for the same internal pressure as the straight pipe. The standard verifies the wall thickness needed according to Annex B; it is listed in Annex D.

The pressure factors on this page are calculated by us – via the equations of Annex B, clause B.4.5, with an arithmetical cross-check (reference in the standard: Annex C).

What this page does not show yet. The increased wall thickness of type B is not given here. We have not yet checked the associated verification route (Annex B, B.5.4) against the values of Annex D – and an unverified number would look on this page exactly like a verified one. It will be added as soon as it is substantiated.

A different quantity is the joint coefficient of welded pipes and fittings – see Joint coefficient.

Installation dimension

The overall length L

The reducer has exactly one overall dimension: L, the length across both welding ends. It depends only on the large end – all small ends of the same run share the same overall length.

The standard dimensions nothing more at the transition: neither the cone angle nor the length of the cylindrical end sections. The drawing above says so in its footer – drawn is the usual shape, dimensioned is what the standard specifies.

The permissible deviations of L are given in EN 10253-4, Table 9; the drawing above shows them in tolerance mode as a second line at the dimension.

Tolerances and testing

Limit deviations and out-of-roundness – per welding end

The drawing above carries the complete tolerance block – here the points that are particular to the reducer:

  • Each end counts with its own diameter. The standard measures “the corresponding outside diameters (D–D1) … at the welding ends” (clause 11.2.1.1). For the small end, the diameter and wall thickness limit deviations therefore apply with D1 and T1 – not with the values of the large end. For a 711 – 508 the large end can thus lie in a different band from the small end.
  • No out-of-roundness limit at the fitting body. The 4 % at the body applies, according to clause 11.2.2, only “to elbows and 180° elbows”. At the welding ends the graduation of Part 4 applies – for each end with its own diameter: up to ⌀ 406.4 included in the diameter limit deviation, above that 2 % at a ratio D/T up to 100, otherwise by agreement.
  • No form tolerance P. In the overall dimension table it is expressly listed as a form tolerance for elbows.

Above ⌀ 610 mm the wall thickness limit deviations depend on whether the fitting is seamless or welded – again for each end with its own diameter and wall thickness. Below that, the distinction makes no difference to the dimensions.

Limits of this page

Which sizes this page shows – and where they come from

For each run, the dimension table of the standard names a range of possible small ends (“57 × 26.9 to 48.3”) – which sizes lie within it is enumerated one by one by the normative Annex C. That enumeration is the source of the size pairs on this page.

One group deserves a note:

  • Five runs remain without a drawing and without a dimension row (⌀ 57: L 76 mm, small ends 26.9 to 48.3 mm; ⌀ 108: L 102 mm, small ends 48.3 to 88.9 mm; ⌀ 133: L 127 mm, small ends 60.3 to 114.3 mm; ⌀ 159: L 140 mm, small ends 76.1 to 139.7 mm; ⌀ 559: L 508 mm, small ends 355.6 to 508 mm). The dimension table of the standard names an overall length and a range of small ends for them, but Annex C does not enumerate the pairs, and the wall thickness series of the standard (Table 7) do not carry these diameters – without a wall thickness there is neither a drawing to scale nor a complete dimension row. So only the values the standard gives are listed here: overall length and range.

We spell this out instead of silently smoothing it over: a gap that can be seen is something different from a guessed number.

Read on

Dimension tables for reducers in stainless steel: 44 size pairs

Zickwolff dimension overview (standard reference EN 10253-4) – one row per orderable size of large and small end, sorted by the large end. The wall thicknesses apply to the concentric as well as the eccentric design. The link at the end of a row opens the dimensional drawing of exactly that size, and the dimensional drawing at the top of this page lets you select any size.

Dimensions Further deliverable dimensions

Dimensions

T is the wall thickness at the large end, T1 the one at the small end. L is the overall length across both welding ends.

The pressure factor X says what proportion of the pipe pressure a reducer of this size carries. The values are those of tables C.3 (concentric) and C.4 (eccentric) of the standard. We additionally recalculated every cell through the equations of Annex B and matched them in full. α is the largest opening angle for which the row applies – that too is how the standard states it.

Show full table · more than 100 rows
Reducers in stainless steel to EN 10253-4:2025-10, from stock or to order – 105 sizes, one row per orderable size, sorted by the large end, all dimensions in millimetres.
D × TLarge end: outside diameter × wall thickness in mmD1 × T1Small end: outside diameter × wall thickness in mmDNnominal size (large end)DN1nominal size (small end)Loverall length in mmα conc.largest opening angle, concentricα ecc.largest opening angle, eccentricX conc.pressure factor in %X ecc.pressure factor in %Wall thickness seriesDimensional drawingIn the shop · in German · delivery to DE, FR, LU, AT
21.3 × 217.2 × 1.61510288°15°––outside the preferred seriesopen – the dimensional drawing of 21.3 × 2 / 17.2 × 1.6
21.3 × 217.2 × 1.81510288°15°––outside the preferred seriesopen – the dimensional drawing of 21.3 × 2 / 17.2 × 1.8
26.9 × 217.2 × 1.820103812°27°––outside the preferred seriesopen – the dimensional drawing of 26.9 × 2 / 17.2 × 1.81.4571
26.9 × 2.317.2 × 220103812°27°100100Series 5open – the dimensional drawing of 26.9 × 2.3 / 17.2 × 2
26.9 × 221.3 × 22015388°15°––outside the preferred seriesopen – the dimensional drawing of 26.9 × 2 / 21.3 × 21.4571
26.9 × 2.321.3 × 22015388°15°100100Series 5open – the dimensional drawing of 26.9 × 2.3 / 21.3 × 2
33.7 × 221.3 × 225155112°24°––outside the preferred seriesopen – the dimensional drawing of 33.7 × 2 / 21.3 × 21.4571
33.7 × 2.621.3 × 225155112°24°100100Series 5open – the dimensional drawing of 33.7 × 2.6 / 21.3 × 2
33.7 × 2.621.3 × 2.625155112°24°––outside the preferred seriesopen – the dimensional drawing of 33.7 × 2.6 / 21.3 × 2.6
33.7 × 226.9 × 22520517°13°100100Series 2open – the dimensional drawing of 33.7 × 2 / 26.9 × 21.4571
33.7 × 2.626.9 × 2.32520517°13°100100Series 5open – the dimensional drawing of 33.7 × 2.6 / 26.9 × 2.3
42.4 × 221.3 × 232155119°42°––outside the preferred seriesopen – the dimensional drawing of 42.4 × 2 / 21.3 × 21.4571
42.4 × 2.621.3 × 232155119°42°10097Series 5open – the dimensional drawing of 42.4 × 2.6 / 21.3 × 2
42.4 × 226.9 × 232205115°30°100100Series 2open – the dimensional drawing of 42.4 × 2 / 26.9 × 21.4571
42.4 × 2.626.9 × 2.332205115°30°100100Series 5open – the dimensional drawing of 42.4 × 2.6 / 26.9 × 2.3
42.4 × 233.7 × 23225519°16°100100Series 2open – the dimensional drawing of 42.4 × 2 / 33.7 × 21.4571
42.4 × 2.633.7 × 2.33225519°16°––outside the preferred seriesopen – the dimensional drawing of 42.4 × 2.6 / 33.7 × 2.3
42.4 × 2.633.7 × 2.63225519°16°100100Series 5open – the dimensional drawing of 42.4 × 2.6 / 33.7 × 2.6
48.3 × 221.3 × 240156422°37°––outside the preferred seriesopen – the dimensional drawing of 48.3 × 2 / 21.3 × 21.4571
48.3 × 226.9 × 240206416°28°100100Series 2open – the dimensional drawing of 48.3 × 2 / 26.9 × 21.4571
48.3 × 2.626.9 × 2.340206416°28°100100Series 5open – the dimensional drawing of 48.3 × 2.6 / 26.9 × 2.3
48.3 × 233.7 × 240256410°19°100100Series 2open – the dimensional drawing of 48.3 × 2 / 33.7 × 21.4571
48.3 × 2.633.7 × 2.640256410°19°100100Series 5open – the dimensional drawing of 48.3 × 2.6 / 33.7 × 2.6
48.3 × 3.233.7 × 3.240256410°19°––outside the preferred seriesopen – the dimensional drawing of 48.3 × 3.2 / 33.7 × 3.2
48.3 × 242.4 × 24032646°8°100100Series 2open – the dimensional drawing of 48.3 × 2 / 42.4 × 21.4571
48.3 × 2.642.4 × 2.64032646°8°100100Series 5open – the dimensional drawing of 48.3 × 2.6 / 42.4 × 2.6
60.3 × 226.9 × 250207621°36°10094Series 2open – the dimensional drawing of 60.3 × 2 / 26.9 × 21.4571
60.3 × 233.7 × 250257616°29°10099Series 2open – the dimensional drawing of 60.3 × 2 / 33.7 × 21.4571
60.3 × 2.933.7 × 2.650257616°29°100100Series 5open – the dimensional drawing of 60.3 × 2.9 / 33.7 × 2.6
60.3 × 242.4 × 250327611°20°100100Series 2open – the dimensional drawing of 60.3 × 2 / 42.4 × 21.4571
60.3 × 2.942.4 × 2.650327611°20°100100Series 5open – the dimensional drawing of 60.3 × 2.9 / 42.4 × 2.61.4571
60.3 × 248.3 × 25040767°13°100100Series 2open – the dimensional drawing of 60.3 × 2 / 48.3 × 21.4571
60.3 × 2.948.3 × 2.65040767°13°100100Series 5open – the dimensional drawing of 60.3 × 2.9 / 48.3 × 2.6
76.1 × 2.333.7 × 265258923°42°––outside the preferred seriesopen – the dimensional drawing of 76.1 × 2.3 / 33.7 × 2
76.1 × 2.333.7 × 2.365258923°42°10087Series 3open – the dimensional drawing of 76.1 × 2.3 / 33.7 × 2.3
76.1 × 242.4 × 265328918°34°10093Series 2open – the dimensional drawing of 76.1 × 2 / 42.4 × 2
76.1 × 2.342.4 × 265328918°34°––outside the preferred seriesopen – the dimensional drawing of 76.1 × 2.3 / 42.4 × 21.4571
76.1 × 2.942.4 × 2.665328918°34°10097Series 5open – the dimensional drawing of 76.1 × 2.9 / 42.4 × 2.6
76.1 × 248.3 × 265408915°27°10098Series 2open – the dimensional drawing of 76.1 × 2 / 48.3 × 2
76.1 × 2.348.3 × 265408915°27°––outside the preferred seriesopen – the dimensional drawing of 76.1 × 2.3 / 48.3 × 21.4571
76.1 × 2.948.3 × 2.665408915°27°100100Series 5open – the dimensional drawing of 76.1 × 2.9 / 48.3 × 2.6
76.1 × 2.360.3 × 26550899°15°––outside the preferred seriesopen – the dimensional drawing of 76.1 × 2.3 / 60.3 × 21.4571
76.1 × 2.960.3 × 2.96550899°15°100100Series 5open – the dimensional drawing of 76.1 × 2.9 / 60.3 × 2.9
88.9 × 2.342.4 × 280328926°50°9977Series 2open – the dimensional drawing of 88.9 × 2.3 / 42.4 × 2
88.9 × 2.642.4 × 280328926°50°––outside the preferred seriesopen – the dimensional drawing of 88.9 × 2.6 / 42.4 × 2
88.9 × 3.242.4 × 2.680328926°50°10080Series 5open – the dimensional drawing of 88.9 × 3.2 / 42.4 × 2.6
88.9 × 2.348.3 × 280408922°44°10084Series 2open – the dimensional drawing of 88.9 × 2.3 / 48.3 × 21.4571
88.9 × 2.648.3 × 280408922°44°––outside the preferred seriesopen – the dimensional drawing of 88.9 × 2.6 / 48.3 × 2
88.9 × 3.248.3 × 2.680408922°44°10087Series 5open – the dimensional drawing of 88.9 × 3.2 / 48.3 × 2.6
88.9 × 2.360.3 × 280508916°30°10096Series 2open – the dimensional drawing of 88.9 × 2.3 / 60.3 × 21.4571
88.9 × 2.660.3 × 280508916°30°––outside the preferred seriesopen – the dimensional drawing of 88.9 × 2.6 / 60.3 × 2
88.9 × 3.260.3 × 2.980508916°30°10099Series 5open – the dimensional drawing of 88.9 × 3.2 / 60.3 × 2.9
88.9 × 2.376.1 × 28065897°13°100100Series 2open – the dimensional drawing of 88.9 × 2.3 / 76.1 × 2
88.9 × 2.376.1 × 2.38065897°13°––outside the preferred seriesopen – the dimensional drawing of 88.9 × 2.3 / 76.1 × 2.31.4571
88.9 × 2.676.1 × 2.38065897°13°100100Series 3open – the dimensional drawing of 88.9 × 2.6 / 76.1 × 2.3
88.9 × 3.276.1 × 2.98065897°13°100100Series 5open – the dimensional drawing of 88.9 × 3.2 / 76.1 × 2.9
114.3 × 2.648.3 × 21004010231°60°95(62)Series 2open – the dimensional drawing of 114.3 × 2.6 / 48.3 × 21.4571
114.3 × 2.360.3 × 21005010226°51°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.3 / 60.3 × 2
114.3 × 2.660.3 × 21005010226°51°98(74)Series 2open – the dimensional drawing of 114.3 × 2.6 / 60.3 × 21.4571
114.3 × 2.660.3 × 2.31005010226°51°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.6 / 60.3 × 2.3
114.3 × 3.660.3 × 2.91005010226°51°10078Series 5open – the dimensional drawing of 114.3 × 3.6 / 60.3 × 2.9
114.3 × 2.376.1 × 21006510218°37°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.3 / 76.1 × 2
114.3 × 2.676.1 × 2.31006510218°37°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.6 / 76.1 × 2.31.4571
114.3 × 3.676.1 × 2.91006510218°37°10093Series 5open – the dimensional drawing of 114.3 × 3.6 / 76.1 × 2.9
114.3 × 2.388.9 × 21008010213°24°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.3 / 88.9 × 2
114.3 × 2.688.9 × 2.31008010213°24°10099Series 2open – the dimensional drawing of 114.3 × 2.6 / 88.9 × 2.31.4571
114.3 × 2.688.9 × 2.61008010213°24°––outside the preferred seriesopen – the dimensional drawing of 114.3 × 2.6 / 88.9 × 2.6
114.3 × 3.688.9 × 3.21008010213°24°100100Series 5open – the dimensional drawing of 114.3 × 3.6 / 88.9 × 3.2
139.7 × 2.960.3 × 2.31255012730°51°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.9 / 60.3 × 2.3
139.7 × 2.676.1 × 2.31256512725°43°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.6 / 76.1 × 2.3
139.7 × 2.976.1 × 2.31256512725°43°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.9 / 76.1 × 2.3
139.7 × 476.1 × 2.91256512725°43°10086Series 5open – the dimensional drawing of 139.7 × 4 / 76.1 × 2.9
139.7 × 2.688.9 × 21258012720°35°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.6 / 88.9 × 2
139.7 × 2.688.9 × 2.31258012720°35°10090Series 2open – the dimensional drawing of 139.7 × 2.6 / 88.9 × 2.3
139.7 × 488.9 × 3.21258012720°35°10093Series 5open – the dimensional drawing of 139.7 × 4 / 88.9 × 3.2
139.7 × 2.6114.3 × 2.312510012710°18°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.6 / 114.3 × 2.3
139.7 × 2.6114.3 × 2.612510012710°18°100100Series 2open – the dimensional drawing of 139.7 × 2.6 / 114.3 × 2.61.4571
139.7 × 2.9114.3 × 2.612510012710°18°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 2.9 / 114.3 × 2.6
139.7 × 4114.3 × 2.612510012710°18°––outside the preferred seriesopen – the dimensional drawing of 139.7 × 4 / 114.3 × 2.6
139.7 × 4114.3 × 3.612510012710°18°100100Series 5open – the dimensional drawing of 139.7 × 4 / 114.3 × 3.6
168.3 × 2.676.1 × 2.31506514031°52°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.6 / 76.1 × 2.3
168.3 × 2.976.1 × 2.31506514031°52°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.9 / 76.1 × 2.3
168.3 × 2.688.9 × 2.31508014027°48°95(76)Series 2open – the dimensional drawing of 168.3 × 2.6 / 88.9 × 2.3
168.3 × 2.988.9 × 2.31508014027°48°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.9 / 88.9 × 2.3
168.3 × 4.588.9 × 3.21508014027°48°9880Series 5open – the dimensional drawing of 168.3 × 4.5 / 88.9 × 3.2
168.3 × 2.6114.3 × 2.315010014019°34°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.6 / 114.3 × 2.3
168.3 × 2.6114.3 × 2.615010014019°34°9990Series 2open – the dimensional drawing of 168.3 × 2.6 / 114.3 × 2.61.4571
168.3 × 2.9114.3 × 2.615010014019°34°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.9 / 114.3 × 2.6
168.3 × 4.5114.3 × 3.615010014019°34°10094Series 5open – the dimensional drawing of 168.3 × 4.5 / 114.3 × 3.6
168.3 × 2.6139.7 × 2.61501251409°18°100100Series 2open – the dimensional drawing of 168.3 × 2.6 / 139.7 × 2.6
168.3 × 2.9139.7 × 2.61501251409°18°––outside the preferred seriesopen – the dimensional drawing of 168.3 × 2.9 / 139.7 × 2.6
168.3 × 4.5139.7 × 41501251409°18°100100Series 5open – the dimensional drawing of 168.3 × 4.5 / 139.7 × 4
219.1 × 2.9114.3 × 2.620010015233°55°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 2.9 / 114.3 × 2.6
219.1 × 2.9139.7 × 2.620012515227°45°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 2.9 / 139.7 × 2.6
219.1 × 2.9139.7 × 2.920012515227°45°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 2.9 / 139.7 × 2.9
219.1 × 3139.7 × 320012515227°45°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 3 / 139.7 × 3
219.1 × 2.9168.3 × 2.620015015218°31°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 2.9 / 168.3 × 2.6
219.1 × 2.9168.3 × 2.920015015218°31°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 2.9 / 168.3 × 2.9
219.1 × 3168.3 × 320015015218°31°––outside the preferred seriesopen – the dimensional drawing of 219.1 × 3 / 168.3 × 3
273 × 3114.3 × 325010017840°60°––outside the preferred seriesopen – the dimensional drawing of 273 × 3 / 114.3 × 3
273 × 3168.3 × 325015017830°48°––outside the preferred seriesopen – the dimensional drawing of 273 × 3 / 168.3 × 3
273 × 3219.1 × 325020017816°28°––outside the preferred seriesopen – the dimensional drawing of 273 × 3 / 219.1 × 3
273 × 4219.1 × 425020017816°28°––outside the preferred seriesopen – the dimensional drawing of 273 × 4 / 219.1 × 4
323.9 × 3219.1 × 330020020324°44°––outside the preferred seriesopen – the dimensional drawing of 323.9 × 3 / 219.1 × 3
323.9 × 3273 × 330025020312°23°––outside the preferred seriesopen – the dimensional drawing of 323.9 × 3 / 273 × 3

standard dimension: D, D1, L, T, T1 · assignment: DN, DN1

( ) Values in brackets apply only if the cylindrical end lengths reach the minimum values to Annex B, or if the reducer sits between pipes of wall thickness T and T1 respectively – that is how the standard states it. 3 cells

Where a dash stands, EN 10253-4 gives the value through the series number – and this row has no series number. This affects the guide mass from the catalogue table and, on the pipe end closures, the pressure factor and the type B wall thickness from the annexes. Nothing is calculated in their place.

Further deliverable dimensions (6)

Further deliverable dimensions – 6 rows, from stock or to order, all dimensions in millimetres.
Doutside diameter (large end) in mmD1outside diameter (small end) in mmTwall thickness (large end) in mmT1wall thickness (small end) in mm
219.188.96.33.2
219.188.985.6
219.188.912.58
273139.722
355.6323.944
406.4323.944

Order dimensions and values calculated by us; deliverable from stock or to order, availability on request. Limit deviations and figures from the standard: see the main table and the standard itself.

The dimensions given are nominal dimensions. The text of the standard prevails. The German edition DIN EN 10253-4:2025-10 reproduces the European version EN 10253-4:2025.

Stainless reducers by dimension – ask our warehouse

You know both ends? Send us the two outside diameters with their wall thicknesses and the design, together with the material grade and the inspection document required. Our export team answers with price, availability and certificate.

Send an inquiry

Frequently asked questions

Where do I find the dimensions of a stainless steel reducer DN 50 to DN 40 to EN 10253-4?

The dimension table on this page lists all available sizes to EN 10253-4; the dimensional drawing above it shows the selected size with all dimensions and tolerances and can be printed as a PDF - the data sheet for your size.

Where is the wall thickness of a fitting measured – and does it apply in the bend?

At the welding end, as the full wall the way the standard enters T at the end plane – not at the root face and not across an inside taper (EN 10253-2 and -4, clauses 11.2.1 and 11.2.3). In the bend the wall may be thinner, but for type A fittings it must not fall below the lower limit for the welding ends. There is no upper limit on the body.

About this dimension table

All dimensions of the stainless steel reducer to EN 10253-4 in one table, the dimensional drawing of your size above it – available from stock or to order. Reducers in stainless steel are covered by a part of the fittings standard of their own: EN 10253-4. It is built to the same pattern as part 2 for steel – and gives different figures throughout. This page carries those figures: pick the design, the large end, the small end and the wall thickness series, and the page shows the dimensional drawing, the dimension table and the limit deviations for exactly that size. What separates the concentric from the eccentric reducer, and how type A differs from type B, is explained on the reducer basics page.

The dimensional drawing – also called dimension sheet, outline drawing or dimension sketch – shows every dimension and the tolerances for your size.

Your inquiry to Zickwolff

Send us what you have – designation, standard, quantity, date. We will clarify the rest with you.

Related pages

← Back to the English knowledge hub

How this data is compiled. This page does not reproduce a standard. It shows the dimensions you need for an inquiry, an order and installation – for sizes we supply, checked against manufacturers’ and suppliers’ documentation and against our own product data. What you see here is what the market supplies, checked against the standard – or calculated by us. How we select our sources and keep them up to date: About this knowledge.

Technical basis: DIN EN 10253-4:2025-10 (butt-welding fittings of stainless steel), EN 10253-2, EN 10204. All information without guarantee – the current standard texts and the manufacturers’ technical data sheets always prevail.

We supply this material – availability, delivery options and inquiry on the supply page →

Ask the Wolf