Skip to main content

A service of Otto Zickwolff GmbH, Germany

Dimension tables & drawingsVisit our shop →

Standards guide · Steel tees

Steel tee: dimensions and dimensional drawing to EN 10253-2

EN 10253-2 (formerly DIN 2615)D 21.3–1219 mmDimensions in mmfrom stock or to order

Standard
EN 10253-2:2026-07
Material
non-alloy and alloy steel
Branch
equal / reducing
Dimensions
F / G

Dimensional drawing for your size

Design variant

EN 10253-2 covers the greyed-out sizes. Our dimension overview lists them as order dimensions – see the table “Further deliverable dimensions” below.

Steel tee · type A · 114.3 × 3.6 – 88.9 × 3.2 mm

Steel tee EN 10253-2 in 3D – rotatable, all sizes 21.3 to 508 mm

Steel tee EN 10253-2, 114.3 × 88.9 mm – 3D view
Typical design as a 3D view: Steel tee EN 10253-2, 114.3 × 88.9 mm. Own illustration based on the dimensions on this page.
Dimensional drawing of a tee in steel, with a reducing branch, 114.3 × 3.6 – 88.9 × 3.2 mm 114.3 (D) 3.6 (T) 88.9 (D1) 3.2 (T1) © zickwolff.de 105 (F) 98 (G) run branch Steel tee · type A · 114.3 × 3.6 – 88.9 × 3.2 mm DIN EN 10253-2:2026-07 · Data as of 2026-08-18 · all dimensions in mm · to scale F is the centre-to-end dimension from the centreline of the branch to the weld end of the run – the overall length across both ends is 2 × F · G is the centre-to-end dimension from the centreline of the run to the weld end of the branch the two circles are the view onto the weld ends, at the scale of the drawing above – on the left the run, on the right the branch the transition between run and branch is drawn as a radius – the standard requires a smooth transition there but does not specify its shape · drawing calculated from the dimensions of the standard · Otto Zickwolff GmbH · zickwolff.de/wissen
Tee in steel, with a reducing branch, type A, 114.3 × 3.6 – 88.9 × 3.2 mm: section in the plane of the axes with F and G, below it the cross-section at the weld end of the run. The transition between run and branch is drawn as a radius – the standard requires a smooth transition there but does not specify its shape.
How to use the dimensional drawing – with example and direct link

Select run, branch and wall thickness – the drawing and the dimension table then show exactly that size, with the figures in the drawing itself instead of only the dimension letters. For an equal tee, pick the same diameter for the branch as for the run. What separates an equal from a reducing branch, and type A from type B is on the tee basics page. The dimension tables for the size pairs listed here are further down this page.

How it works: Choose 114.3 mm in the field “Outside diameter”, 88.9 mm in the field “Branch” and Series 2 in the field “Wall thickness”. The dimensional drawing immediately shows every dimension of the steel tee with tolerances, the table below all sizes. “Print this size as PDF” takes the drawing with you.

Example reducing branch, 114.3 × 3.6 – 88.9 × 3.2 mm: outside diameter, run D 114.3 mm, wall thickness, run T 3.6 mm, inside diameter, run ID 107.1 mm, outside diameter, branch D1 88.9 mm, wall thickness, branch T1 3.2 mm, inside diameter, branch ID1 82.5 mm, mass 3.3 kg.

Direct link to this size: https://www.zickwolff.de/wissen/en/tees-steel/?d=114.3&d1=88.9&reihe=2

Technical basis: DIN EN 10253-2:2026-07. Zickwolff has prepared this presentation for practical use, with our own structure, our own designations and a statement of what kind of value each figure is. The original standard governs normative requirements.

Dimensions of the tee in steel, reducing branch, 114.3 × 3.6 – 88.9 × 3.2 mm
PropertyValueType of information
basic data
branchreducingcalculated
Wall thickness seriesSeries 2standard dimension
Availabilityfrom stock or to ordertrade information
nominal size DN, runDN 100assignment
nominal size DN, branchDN 80assignment
mass3.3 kgguide value
connecting dimensions The dimensions at the welding ends that govern the joint with the pipe that follows.
outside diameter, run D114.3 mmstandard dimension
wall thickness, run T3.6 mmstandard dimension
inside diameter, run ID107.1 mmcalculated
outside diameter, branch D188.9 mmstandard dimension
wall thickness, branch T13.2 mmstandard dimension
inside diameter, branch ID182.5 mmcalculated
installation dimensions The dimensions that determine the installation space.
centre-to-end dimension, run F105 mmstandard dimension
centre-to-end dimension, branch G98 mmstandard dimension
type A or type B Both designs in the standard have identical connecting dimensions. They differ in exactly these two values – type A carries less internal pressure than the straight pipe, type B is reinforced at the fitting body so that it matches it.
pressure factor (type A only) X37 %calculated
wall thickness at the fitting body, run (type B only) Ts7.9 mmstandard value (not binding)
wall thickness at the fitting body, branch (type B only) Tb6 mmstandard value (not binding)

Without an entry in the “Type of information” column: standard dimension. A dimension that EN 10253-2 specifies for this size.

Where exactly it is measured

outside diameter, run D
measured across the edge at the welding ends of the run pipe
outside diameter, branch D1
measured at the welding end of the branch – on an equal tee D1 = D
wall thickness, run T
at the welding end of the run – on the fitting body it may deviate downwards
wall thickness, branch T1
at the welding end of the branch – the series is the same as on the run, the value belongs to diameter D1
centre-to-end dimension, run F
from the centreline of the branch to the welding end of the run – the overall dimension across both ends is 2 × F
centre-to-end dimension, branch G
from the centreline of the run to the welding end of the branch
nominal size DN, run
the customary pipe designation – it is NOT given in EN 10253 but comes from the pipe dimension world
nominal size DN, branch
assigned via the outside diameter of the branch, otherwise as for the run
inside diameter, run ID
clear bore – the standard defines it as D minus twice T
inside diameter, branch ID1
ID1 = D1 minus twice T1
pressure factor (type A only) X
ratio of the pressure resistance of the fitting to that of a pipe of the same wall thickness – not a measured value but calculated
mass
guide value for estimating freight and loads
wall thickness at the fitting body, run (type B only) Ts
measured on the body of the run – T still applies at the welding ends
wall thickness at the fitting body, branch (type B only) Tb
measured on the body of the branch – T1 still applies at the welding ends

Not in the dimensional drawing: ⌀ 21.3 – 17.2, ⌀ 26.9 – 17.2 – the standard gives no wall thickness series for one of the two diameters, and without a wall thickness there is neither a scale drawing nor a complete dimension row

Not in the dimensional drawing: ⌀ 60.3 – 57, ⌀ 76.1 – 57, ⌀ 88.9 – 57, ⌀ 114.3 – 57, ⌀ 114.3 – 108, ⌀ 139.7 – 108, ⌀ 139.7 – 133, ⌀ 168.3 – 108, ⌀ 168.3 – 133, ⌀ 168.3 – 159, ⌀ 219.1 – 108, ⌀ 219.1 – 133, ⌀ 219.1 – 159, ⌀ 273 – 133, ⌀ 273 – 159, ⌀ 323.9 – 159, ⌀ 1219 – 1168 – the standard carries a dash in place of the G dimension and names this branch only with an equal run

Dimensions are nominal dimensions to EN 10253-2 and do not replace the data sheet of the actual item. No statement about pressure or temperature suitability and no statement about the material. F and G are dimensions measured from the centreline – the overall length across both run ends is 2 × F. Direct link to this size

Where it is measured – at the welding end

Measured at the welding end – D on the extended cylindrical outside surface, T as the full wall to the inside surface, as the standard enters both at the end plane – not at the root face.

inside of the pipeTDbevel 30° +5/−0root face C 1.6 ± 0.8 mm
Wall section at the welding end – not to scale. Image: Zickwolff
inside of the pipeTDbevel 30° +5/−0outside ≤ 30°inside ≤ 18°root face C 1.6 ± 0.8 mm
Machined end: chamfered outside up to 30° and inside up to 18° – the wall at the end may become thinner. T is dimensioned at the end plane from the end of the outer chamfer to the end of the inner chamfer, as in the standard figure. Not to scale. Image: Zickwolff

EN 10253-2 and EN 10253-4 measure outside diameter D and wall thickness T at the welding ends. In the standard’s figure both are entered at the end plane: D on the extended cylindrical outside surface, T as the full wall between the extended outside surface and the inside surface – the bevel only appears to cut the wall. The root face C of 1.6 ± 0.8 mm is not T. If the end is machined (chamfered outside up to 30° and inside up to 18°, which the standard expressly allows), T runs from the edge where the outer chamfer ends to the edge where the inner chamfer ends. On the body of an elbow the wall may be thinner – only the lower limit of table 12 applies there (type A), and no upper limit is defined for the body. The diameter on the body is limited only by out-of-roundness.

Typical measuring error: Measuring with the caliper across the bevel or the inside taper gives too small a wall – a conforming fitting is then wrongly rejected.

Rule of thumb: Measure the full wall – not the root face.

The standard names dimensions. What is listed here, we carry – from stock or to order; how quickly a size is available we clarify on request.

How to measure correctly

A tee is measured at three ends: outside diameter D and wall thickness T at the run, D1 and T1 at the branch – on an equal tee D1 equals D. The centre-to-end dimension F runs from the centre line of the branch to the welding end of the run, so the overall length is 2 × F. G runs from the centre line of the run to the welding end of the branch.

outside diameter, run D
measured across the edge at the welding ends of the run pipe
outside diameter, branch D1
measured at the welding end of the branch – on an equal tee D1 = D
wall thickness, run T
at the welding end of the run – on the fitting body it may deviate downwards
wall thickness, branch T1
at the welding end of the branch – the series is the same as on the run, the value belongs to diameter D1
centre-to-end dimension, run F
from the centreline of the branch to the welding end of the run – the overall dimension across both ends is 2 × F
centre-to-end dimension, branch G
from the centreline of the run to the welding end of the branch

A measured value rarely matches the table exactly. The dimensional drawing on this page shows the limit deviations of EN 10253-2 for every size.

Branch

Equal and reducing branch

A tee with an equal branch – in the German trade almost always called “egal”, from the English equal tee – has the same nominal size in the branch as in the run. With a reducing branch the branch is smaller.

The standard does not list this as a feature of its own. It decides it via the dimension statement: “If only one dimension pair is given (D × T), an equal tee is meant” (EN 10253-2, clause 5.3.4). Two dimension pairs therefore mean a reducing branch – the order needs nothing more than that.

Both are listed in one dimension table (Table A.2) with the same four dimensions D, D1, F and G. That is why the dimensional drawing above also shows both: you select the run, and if you need a smaller branch, the second field appears.

Rows of black steel tees with bevelled welding ends and stamped material marking on the rack
Steel tees with equal branch. The ends are bevelled – whether that is so is decided by the wall thickness (see below). The marking is on the body, not at the end.

Not every size exists as a reducing tee. For the branches ⌀ 57, 108, 133, 159 and 1168 mm the dimension table carries a dash in column G: these sizes are standardised with an equal branch only. The dimensional drawing therefore does not offer them as a reducing branch – that is not a gap in our data but a statement of the standard.

Type A and type B

Type A and type B: the pressure factor

At the place where the branch sits, a tee has an opening in the pipe wall – and hence, at that place, less load-bearing cross-section than a straight pipe. The standard describes this with two versions:

Version

Type A – reduced pressure factor

Wall thickness at the fitting body as at the welding ends. The internal pressure the part withstands is lower than that of the straight pipe of the same wall thickness. How much lower is stated by the pressure factor X in per cent – it is given in the dimension table above for every size.

Version

Type B – full pressure resistance (standard: “for use at full service pressure”)

Increased wall thickness at the fitting body, designed for the same internal pressure as the straight pipe. The standard calculates the wall thickness needed according to Annex B; it is listed in Annex D.

The pressure factor in our table is calculated by us – according to the equations of Annex B, clause B.4.4, with an arithmetical cross-check. The advantage of a calculated value: it applies to every size, not only to a selection.

The type B wall thickness is a solution, not the solution. If you switch to type B above, Ts (run) and Tb (branch) appear in the dimension table and in the drawing. Both values are non-binding: the standard names them but does not specify them. There is a factual reason for this – for tees, Annex B gives not a calculation but a verification procedure (B.5.3). A size therefore has not one permissible wall thickness but a range; for roughly four out of ten rows, one tenth of a millimetre thinner would be permissible too. Our values are arithmetically cross-checked by this procedure. What governs an ordered part is the verification according to Annex B, not the table.

A different quantity is the joint coefficient of welded pipes and fittings – see Joint coefficient.

Installation dimensions

The overall dimensions F and G

The tee has two centre-to-end dimensions, and both are measured from the centre line – not across the whole part:

  • F – from the centre line of the branch to the welding end of the run. The overall length across both run ends is therefore 2 × F, not F.
  • G – from the centre line of the run to the welding end of the branch.

F depends only on the run diameter and is the same for all branches of the same size. G, by contrast, changes with the branch – that is why the dimension table carries a row of its own for each pair (D, D1).

The permissible deviations of both dimensions are given in EN 10253-2, Table 13; the drawing above shows them in tolerance mode as a second line at the dimension.

Tolerances and testing

Limit deviations, out-of-roundness and inside diameter

The drawing above carries the complete tolerance block – here the points that differ for the tee from the other fittings of the series of standards:

  • Inside diameter: 70 %, not 80 %. The inside diameter must at every point of the fitting exceed 80 % of the inside diameter at the welding ends – for tees the standard expressly names 70 % (clause 11.2.1.2). That is the consequence of the branch opening.
  • No out-of-roundness limit at the fitting body. The 4 % at the body applies, according to clause 11.2.2, only “to elbows and 180° elbows”. At the welding ends of the tee the general rule applies.
  • No form tolerance P. In the overall dimension table it is expressly listed as a form tolerance for elbows.

Above ⌀ 610 mm the wall thickness limit deviations depend on whether the fitting is seamless or welded. Below that, the distinction makes no difference to the dimensions – and the standard leaves the choice of pipe to the manufacturer anyway, as long as the order specifies nothing else. What exactly “seamless” and “welded” mean here is explained on the general tee page.

Limits of this page

Out-of-roundness compared: tube standards and EN 10253-2

The box above says it in words – here the figures stand side by side. For the fitting, measurement is at the welding ends; the tube values apply to the tube that arrives there.

Out-of-roundness compared: tube standards and fitting standard
StandardRangeOut-of-roundness
EN 10216 (seamless, boiler tube)–names no out-of-roundness limit
EN 10217 (welded)D > 406.4 and D/T ≤ 100< 2 %
EN 10208 (line pipe)D ≤ 610< 2 %
EN 10208 (line pipe)D > 610 and D/T ≤ 75< 1.5 %, at most 15 mm
EN 10208 (line pipe)D > 610 and D/T > 75< 2.0 %
API 5Lall± 1.0 % · dₐ
EN 10253-2at the welding end, ⌀ ≤ 273included in the diameter limit deviation
EN 10253-2at the welding end, 273 < ⌀ ≤ 610≤ 2 %
EN 10253-2at the welding end, ⌀ > 610≤ 1 %

At the branch the same graduation applies with the diameter of this end (D1) – a reducing tee is therefore assessed per end.

Fitting values: EN 10253-2, 11.2.2 · tube values: limit deviations of the tube standards EN 10216 and EN 10217

Which sizes this page shows – and which it does not

The dimensional drawing shows every combination of run, branch and wall thickness series for which EN 10253-2 names a wall thickness. Two groups are missing, and both are missing for a reason the standard itself gives:

  • Sizes without a wall thickness series. Without a wall thickness there is neither a drawing to scale nor a complete dimension row – a number would have to be invented. The dimensions the standard gives for these diameters are listed in the dimension tables further down.
  • Branches standardised as equal tees only. For ⌀ 57, 108, 133, 159 and 1168 mm the standard carries a dash in column G.

We spell out both instead of silently omitting the sizes: a gap that can be seen is something different from one that is taken for completeness.

Read on

Dimension tables for tees in steel: 73 size pairs

Zickwolff dimension overview (standard reference EN 10253-2) – one row per orderable size of run and branch, sorted by the run. The link at the end of a row opens the dimensional drawing of exactly that size, and the dimensional drawing at the top of this page lets you select any size.

Dimensions Type B wall thicknesses Further deliverable dimensions

Dimensions

T is the wall thickness of the run, T1 that of the branch. F and G are dimensions measured from the centre line – the overall length across both run ends is 2 × F. The pressure factor X is not a figure from the dimension table but calculated to Annex B, and it applies to design type A only.

Show full table · more than 200 rows
Tees in steel to EN 10253-2:2026-07, from stock or to order – 110 sizes, one row per orderable size, sorted by the run, all dimensions in millimetres.
D × TRun: outside diameter × wall thickness in mmD1 × T1Branch: outside diameter × wall thickness in mmDNnominal size DN, runDN1nominal size DN, branchFcentre-to-end dimension, run in mmGcentre-to-end dimension, branch in mmXpressure factor (type A only) in %Wall thickness seriesDimensional drawingIn the shop · in German · delivery to DE, FR, LU, AT
21.3 × 221.3 × 21515252542Series 2open – the dimensional drawing of 21.3 × 2 / 21.3 × 2P235GH
21.3 × 421.3 × 41515252551Series 5open – the dimensional drawing of 21.3 × 4 / 21.3 × 4
26.9 × 2.321.3 × 22015292944Series 2open – the dimensional drawing of 26.9 × 2.3 / 21.3 × 2P235GH
26.9 × 421.3 × 42015292957Series 5open – the dimensional drawing of 26.9 × 4 / 21.3 × 4
26.9 × 2.326.9 × 2.32020292943Series 2open – the dimensional drawing of 26.9 × 2.3 / 26.9 × 2.3P235GH
26.9 × 3.226.9 × 3.22020292947Series 4open – the dimensional drawing of 26.9 × 3.2 / 26.9 × 3.2
33.7 × 2.621.3 × 22515383843Series 2open – the dimensional drawing of 33.7 × 2.6 / 21.3 × 2P235GH
33.7 × 421.3 × 3.22515383850Series 4open – the dimensional drawing of 33.7 × 4 / 21.3 × 3.2
33.7 × 2.626.9 × 2.32520383842Series 2open – the dimensional drawing of 33.7 × 2.6 / 26.9 × 2.3P235GH
33.7 × 2.633.7 × 2.62525383841Series 2open – the dimensional drawing of 33.7 × 2.6 / 33.7 × 2.6P235GH
33.7 × 3.233.7 × 3.22525383843Series 3open – the dimensional drawing of 33.7 × 3.2 / 33.7 × 3.2
33.7 × 433.7 × 42525383846Series 4open – the dimensional drawing of 33.7 × 4 / 33.7 × 4
42.4 × 2.621.3 × 23215484844Series 2open – the dimensional drawing of 42.4 × 2.6 / 21.3 × 2
42.4 × 2.626.9 × 2.33220484843Series 2open – the dimensional drawing of 42.4 × 2.6 / 26.9 × 2.3P235GH
42.4 × 2.633.7 × 2.63225484842Series 2open – the dimensional drawing of 42.4 × 2.6 / 33.7 × 2.6P235GH
42.4 × 2.642.4 × 2.63232484838Series 2open – the dimensional drawing of 42.4 × 2.6 / 42.4 × 2.6P235GH
42.4 × 3.642.4 × 3.63232484842Series 3open – the dimensional drawing of 42.4 × 3.6 / 42.4 × 3.6
42.4 × 442.4 × 43232484843Series 4open – the dimensional drawing of 42.4 × 4 / 42.4 × 4
48.3 × 2.621.3 × 24015575742Series 2open – the dimensional drawing of 48.3 × 2.6 / 21.3 × 2P235GH
48.3 × 2.626.9 × 2.34020575742Series 2open – the dimensional drawing of 48.3 × 2.6 / 26.9 × 2.3P235GH
48.3 × 2.633.7 × 2.64025575742Series 2open – the dimensional drawing of 48.3 × 2.6 / 33.7 × 2.6P235GH
48.3 × 433.7 × 3.24025575742outside the preferred seriesopen – the dimensional drawing of 48.3 × 4 / 33.7 × 3.2
48.3 × 433.7 × 44025575748Series 4open – the dimensional drawing of 48.3 × 4 / 33.7 × 4
48.3 × 2.642.4 × 2.64032575738Series 2open – the dimensional drawing of 48.3 × 2.6 / 42.4 × 2.6P235GH
48.3 × 2.648.3 × 2.64040575735Series 2open – the dimensional drawing of 48.3 × 2.6 / 48.3 × 2.6P235GH
48.3 × 448.3 × 44040575740Series 4open – the dimensional drawing of 48.3 × 4 / 48.3 × 4
48.3 × 548.3 × 54040575743Series 5open – the dimensional drawing of 48.3 × 5 / 48.3 × 5
48.3 × 6.348.3 × 6.34040575746Series 6open – the dimensional drawing of 48.3 × 6.3 / 48.3 × 6.3
57 × 2.957 × 2.9––646436Series 2open – the dimensional drawing of 57 × 2.9 / 57 × 2.9P235GH
60.3 × 2.926.9 × 2.35020644458Series 2open – the dimensional drawing of 60.3 × 2.9 / 26.9 × 2.3P235GH
60.3 × 2.933.7 × 2.65025645151Series 2open – the dimensional drawing of 60.3 × 2.9 / 33.7 × 2.6P235GH
60.3 × 5.633.7 × 5.65025645166outside the preferred seriesopen – the dimensional drawing of 60.3 × 5.6 / 33.7 × 5.6
60.3 × 2.942.4 × 2.65032645743Series 2open – the dimensional drawing of 60.3 × 2.9 / 42.4 × 2.6P235GH
60.3 × 4.542.4 × 3.65032645746outside the preferred seriesopen – the dimensional drawing of 60.3 × 4.5 / 42.4 × 3.6
60.3 × 2.948.3 × 2.65040646039Series 2open – the dimensional drawing of 60.3 × 2.9 / 48.3 × 2.6P235GH
60.3 × 4.548.3 × 45040646045outside the preferred seriesopen – the dimensional drawing of 60.3 × 4.5 / 48.3 × 4
60.3 × 2.960.3 × 2.95050646436Series 2open – the dimensional drawing of 60.3 × 2.9 / 60.3 × 2.9P235GH
60.3 × 4.560.3 × 4.55050646441outside the preferred seriesopen – the dimensional drawing of 60.3 × 4.5 / 60.3 × 4.5
60.3 × 5.660.3 × 5.65050646444Series 5open – the dimensional drawing of 60.3 × 5.6 / 60.3 × 5.6
76.1 × 2.933.7 × 2.66525765757Series 2open – the dimensional drawing of 76.1 × 2.9 / 33.7 × 2.6P235GH
76.1 × 2.942.4 × 2.66532766448Series 2open – the dimensional drawing of 76.1 × 2.9 / 42.4 × 2.6P235GH
76.1 × 7.142.4 × 7.16532766467outside the preferred seriesopen – the dimensional drawing of 76.1 × 7.1 / 42.4 × 7.1
76.1 × 2.948.3 × 2.66540766744Series 2open – the dimensional drawing of 76.1 × 2.9 / 48.3 × 2.6P235GH
76.1 × 7.148.3 × 56540766751Series 5open – the dimensional drawing of 76.1 × 7.1 / 48.3 × 5
76.1 × 8.848.3 × 86540766761outside the preferred seriesopen – the dimensional drawing of 76.1 × 8.8 / 48.3 × 8
76.1 × 2.960.3 × 2.96550767041Series 2open – the dimensional drawing of 76.1 × 2.9 / 60.3 × 2.9P235GH
76.1 × 560.3 × 56550767049outside the preferred seriesopen – the dimensional drawing of 76.1 × 5 / 60.3 × 5
76.1 × 2.976.1 × 2.96565767634Series 2open – the dimensional drawing of 76.1 × 2.9 / 76.1 × 2.9P235GH
76.1 × 5.676.1 × 5.66565767643Series 4open – the dimensional drawing of 76.1 × 5.6 / 76.1 × 5.6
76.1 × 7.176.1 × 7.16565767646Series 5open – the dimensional drawing of 76.1 × 7.1 / 76.1 × 7.1
88.9 × 3.242.4 × 2.68032867050Series 2open – the dimensional drawing of 88.9 × 3.2 / 42.4 × 2.6P235GH
88.9 × 3.248.3 × 2.68040867346Series 2open – the dimensional drawing of 88.9 × 3.2 / 48.3 × 2.6P235GH
88.9 × 3.260.3 × 2.98050867642Series 2open – the dimensional drawing of 88.9 × 3.2 / 60.3 × 2.9P235GH
88.9 × 3.276.1 × 2.98065868336Series 2open – the dimensional drawing of 88.9 × 3.2 / 76.1 × 2.9P235GH
88.9 × 3.288.9 × 3.28080868634Series 2open – the dimensional drawing of 88.9 × 3.2 / 88.9 × 3.2P235GH
88.9 × 5.688.9 × 5.68080868641Series 4open – the dimensional drawing of 88.9 × 5.6 / 88.9 × 5.6
88.9 × 888.9 × 88080868646Series 5open – the dimensional drawing of 88.9 × 8 / 88.9 × 8
108 × 3.6108 × 3.6––10010034Series 2open – the dimensional drawing of 108 × 3.6 / 108 × 3.6P235GH
114.3 × 3.648.3 × 2.6100401058649Series 2open – the dimensional drawing of 114.3 × 3.6 / 48.3 × 2.6P235GH
114.3 × 3.660.3 × 2.9100501058945Series 2open – the dimensional drawing of 114.3 × 3.6 / 60.3 × 2.9P235GH
114.3 × 3.676.1 × 2.9100651059539Series 2open – the dimensional drawing of 114.3 × 3.6 / 76.1 × 2.9P235GH
114.3 × 3.688.9 × 3.2100801059837Series 2open – the dimensional drawing of 114.3 × 3.6 / 88.9 × 3.2P235GH
114.3 × 3.6114.3 × 3.610010010510534Series 2open – the dimensional drawing of 114.3 × 3.6 / 114.3 × 3.6P235GH
114.3 × 6.3114.3 × 6.310010010510540Series 4open – the dimensional drawing of 114.3 × 6.3 / 114.3 × 6.3
114.3 × 8.8114.3 × 8.810010010510545Series 5open – the dimensional drawing of 114.3 × 8.8 / 114.3 × 8.8
133 × 4133 × 4––12012033Series 2open – the dimensional drawing of 133 × 4 / 133 × 4P235GH
139.7 × 460.3 × 2.91255012410547Series 2open – the dimensional drawing of 139.7 × 4 / 60.3 × 2.9P235GH
139.7 × 476.1 × 2.91256512410841Series 2open – the dimensional drawing of 139.7 × 4 / 76.1 × 2.9P235GH
139.7 × 488.9 × 3.21258012411139Series 2open – the dimensional drawing of 139.7 × 4 / 88.9 × 3.2P235GH
139.7 × 1088.9 × 101258012411160outside the preferred seriesopen – the dimensional drawing of 139.7 × 10 / 88.9 × 10
139.7 × 4114.3 × 3.612510012411736Series 2open – the dimensional drawing of 139.7 × 4 / 114.3 × 3.6P235GH
139.7 × 4139.7 × 412512512412433Series 2open – the dimensional drawing of 139.7 × 4 / 139.7 × 4P235GH
139.7 × 6.3139.7 × 6.312512512412439Series 4open – the dimensional drawing of 139.7 × 6.3 / 139.7 × 6.3
139.7 × 10139.7 × 1012512512412444Series 5open – the dimensional drawing of 139.7 × 10 / 139.7 × 10
159 × 4.5159 × 4.5––13813833Series 2open – the dimensional drawing of 159 × 4.5 / 159 × 4.5P235GH
168.3 × 4.576.1 × 2.91506514312144Series 2open – the dimensional drawing of 168.3 × 4.5 / 76.1 × 2.9P235GH
168.3 × 4.588.9 × 3.21508014312442Series 2open – the dimensional drawing of 168.3 × 4.5 / 88.9 × 3.2P235GH
168.3 × 4.5114.3 × 3.615010014313038Series 2open – the dimensional drawing of 168.3 × 4.5 / 114.3 × 3.6P235GH
168.3 × 11114.3 × 1115010014313057outside the preferred seriesopen – the dimensional drawing of 168.3 × 11 / 114.3 × 11
168.3 × 4.5139.7 × 415012514313735Series 2open – the dimensional drawing of 168.3 × 4.5 / 139.7 × 4P235GH
168.3 × 4.5168.3 × 4.515015014314333Series 2open – the dimensional drawing of 168.3 × 4.5 / 168.3 × 4.5P235GH
168.3 × 7.1168.3 × 7.115015014314338Series 4open – the dimensional drawing of 168.3 × 7.1 / 168.3 × 7.1
168.3 × 11168.3 × 1115015014314344Series 5open – the dimensional drawing of 168.3 × 11 / 168.3 × 11
219.1 × 6.388.9 × 3.22008017815245Series 2open – the dimensional drawing of 219.1 × 6.3 / 88.9 × 3.2P235GH
219.1 × 6.3114.3 × 3.620010017815640Series 2open – the dimensional drawing of 219.1 × 6.3 / 114.3 × 3.6P235GH
219.1 × 6.3139.7 × 420012517816237Series 2open – the dimensional drawing of 219.1 × 6.3 / 139.7 × 4P235GH
219.1 × 6.3168.3 × 4.520015017816837Series 2open – the dimensional drawing of 219.1 × 6.3 / 168.3 × 4.5P235GH
219.1 × 6.3219.1 × 6.320020017817834Series 2open – the dimensional drawing of 219.1 × 6.3 / 219.1 × 6.3P235GH
219.1 × 8219.1 × 820020017817837Series 4open – the dimensional drawing of 219.1 × 8 / 219.1 × 8
219.1 × 12.5219.1 × 12.520020017817843Series 5open – the dimensional drawing of 219.1 × 12.5 / 219.1 × 12.5
273 × 6.3114.3 × 3.625010021618443Series 2open – the dimensional drawing of 273 × 6.3 / 114.3 × 3.6P235GH
273 × 6.3139.7 × 425012521619140Series 2open – the dimensional drawing of 273 × 6.3 / 139.7 × 4P235GH
273 × 6.3168.3 × 4.525015021619437Series 2open – the dimensional drawing of 273 × 6.3 / 168.3 × 4.5P235GH
273 × 6.3219.1 × 6.325020021620338Series 2open – the dimensional drawing of 273 × 6.3 / 219.1 × 6.3P235GH
273 × 6.3273 × 6.325025021621632Series 2open – the dimensional drawing of 273 × 6.3 / 273 × 6.3P235GH
323.9 × 7.1139.7 × 430012525421642Series 2open – the dimensional drawing of 323.9 × 7.1 / 139.7 × 4P235GH
323.9 × 7.1168.3 × 4.530015025421939Series 2open – the dimensional drawing of 323.9 × 7.1 / 168.3 × 4.5P235GH
323.9 × 7.1219.1 × 6.330020025422939Series 2open – the dimensional drawing of 323.9 × 7.1 / 219.1 × 6.3P235GH
323.9 × 7.1273 × 6.330025025424133Series 2open – the dimensional drawing of 323.9 × 7.1 / 273 × 6.3P235GH
323.9 × 7.1323.9 × 7.130030025425432Series 2open – the dimensional drawing of 323.9 × 7.1 / 323.9 × 7.1P235GH
323.9 × 12.5323.9 × 12.530030025425439Series 5open – the dimensional drawing of 323.9 × 12.5 / 323.9 × 12.5
355.6 × 8168.3 × 4.535015027923840Series 2open – the dimensional drawing of 355.6 × 8 / 168.3 × 4.5P235GH
355.6 × 8323.9 × 7.135030027927033Series 2open – the dimensional drawing of 355.6 × 8 / 323.9 × 7.1P235GH
355.6 × 8355.6 × 835035027927932Series 2open – the dimensional drawing of 355.6 × 8 / 355.6 × 8P235GH
406.4 × 8.8219.1 × 6.340020030527340Series 2open – the dimensional drawing of 406.4 × 8.8 / 219.1 × 6.3P235GH
406.4 × 8.8273 × 6.340025030528335Series 2open – the dimensional drawing of 406.4 × 8.8 / 273 × 6.3P235GH
406.4 × 8.8406.4 × 8.840040030530532Series 2open – the dimensional drawing of 406.4 × 8.8 / 406.4 × 8.8P235GH
457 × 10457 × 1045045034334332Series 2open – the dimensional drawing of 457 × 10 / 457 × 10P235GH
508 × 11406.4 × 8.850040038135633outside the preferred seriesopen – the dimensional drawing of 508 × 11 / 406.4 × 8.8P235GH
508 × 11508 × 1150050038138132Series 3open – the dimensional drawing of 508 × 11 / 508 × 11P235GH

More sizes in the shop (in German): P235GH DIN 2615 (1 size) · P235GH EN 10253-2 (2 sizes)

standard dimension: D, D1, F, G, T, T1 · calculated: X · assignment: DN, DN1

DN and DN1: The standard does not assign a nominal size to every size. Where the dash stands there is none – the size is designated by its outside diameter.

Type B wall thicknesses by series

Ts is the wall thickness at the body of the run, Tb the one at the body of the branch. At the welding ends T and T1 from the table above still apply – the reinforcement lies on the inside and tapers out towards the ends.

These wall thicknesses are not laid down. The wall thickness of a tee is not calculated, it is assumed and then verified. So a size pair does not have one permissible wall thickness but a whole range – the values here are one solution, not the solution, and a manufacturer may deviate as long as the verification works out.

Type B wall thicknesses for tees in steel to EN 10253-2:2026-07, non-binding values – 95 sizes of the wall thickness series for which the annex gives values, all dimensions in millimetres.
D × TRun: outside diameter × wall thickness in mmD1 × T1Branch: outside diameter × wall thickness in mmTswall thickness at the fitting body, run (type B only) in mmTbwall thickness at the fitting body, branch (type B only) in mmWall thickness series
21.3 × 221.3 × 24.23.2Series 2
21.3 × 421.3 × 47.45.6Series 5
26.9 × 2.321.3 × 24.43.3Series 2
26.9 × 421.3 × 46.75.1Series 5
26.9 × 2.326.9 × 2.34.83.6Series 2
26.9 × 3.226.9 × 3.26.34.7Series 4
33.7 × 2.621.3 × 24.83.6Series 2
33.7 × 421.3 × 3.26.75Series 4
33.7 × 2.626.9 × 2.35.23.9Series 2
33.7 × 2.633.7 × 2.65.74.3Series 2
33.7 × 3.233.7 × 3.26.75Series 3
33.7 × 433.7 × 47.95.9Series 4
42.4 × 2.621.3 × 24.83.6Series 2
42.4 × 2.626.9 × 2.35.13.8Series 2
42.4 × 2.633.7 × 2.65.54.1Series 2
42.4 × 2.642.4 × 2.664.5Series 2
42.4 × 3.642.4 × 3.67.75.8Series 3
42.4 × 442.4 × 48.36.3Series 4
48.3 × 2.621.3 × 24.93.7Series 2
48.3 × 2.626.9 × 2.35.23.9Series 2
48.3 × 2.633.7 × 2.65.54.2Series 2
48.3 × 433.7 × 47.75.8Series 4
48.3 × 2.642.4 × 2.664.5Series 2
48.3 × 2.648.3 × 2.66.34.7Series 2
48.3 × 448.3 × 48.76.6Series 4
48.3 × 548.3 × 510.37.8Series 5
48.3 × 6.348.3 × 6.312.39.3Series 6
60.3 × 2.926.9 × 2.34.53.4Series 2
60.3 × 2.933.7 × 2.65.13.8Series 2
60.3 × 2.942.4 × 2.65.84.3Series 2
60.3 × 2.948.3 × 2.66.24.6Series 2
60.3 × 2.960.3 × 2.96.95.2Series 2
60.3 × 5.660.3 × 5.611.48.6Series 5
76.1 × 2.933.7 × 2.64.83.6Series 2
76.1 × 2.942.4 × 2.65.44Series 2
76.1 × 2.948.3 × 2.65.74.3Series 2
76.1 × 7.148.3 × 511.48.5Series 5
76.1 × 2.960.3 × 2.96.34.8Series 2
76.1 × 2.976.1 × 2.97.25.4Series 2
76.1 × 5.676.1 × 5.611.88.9Series 4
76.1 × 7.176.1 × 7.114.410.8Series 5
88.9 × 3.242.4 × 2.65.64.2Series 2
88.9 × 3.248.3 × 2.65.94.4Series 2
88.9 × 3.260.3 × 2.96.54.9Series 2
88.9 × 3.276.1 × 2.97.35.5Series 2
88.9 × 3.288.9 × 3.27.96Series 2
88.9 × 5.688.9 × 5.612.19.1Series 4
88.9 × 888.9 × 816.512.4Series 5
114.3 × 3.648.3 × 2.66.14.6Series 2
114.3 × 3.660.3 × 2.96.65Series 2
114.3 × 3.676.1 × 2.97.45.6Series 2
114.3 × 3.688.9 × 3.27.96Series 2
114.3 × 3.6114.3 × 3.696.8Series 2
114.3 × 6.3114.3 × 6.313.910.4Series 4
114.3 × 8.8114.3 × 8.818.814.1Series 5
139.7 × 460.3 × 2.96.95.2Series 2
139.7 × 476.1 × 2.97.65.7Series 2
139.7 × 488.9 × 3.28.16.1Series 2
139.7 × 4114.3 × 3.69.16.9Series 2
139.7 × 4139.7 × 410.27.6Series 2
139.7 × 6.3139.7 × 6.314.310.8Series 4
139.7 × 10139.7 × 102216.5Series 5
168.3 × 4.576.1 × 2.97.95.9Series 2
168.3 × 4.588.9 × 3.28.46.3Series 2
168.3 × 4.5114.3 × 3.69.47.1Series 2
168.3 × 4.5139.7 × 410.47.8Series 2
168.3 × 4.5168.3 × 4.511.58.6Series 2
168.3 × 7.1168.3 × 7.116.512.4Series 4
168.3 × 11168.3 × 1125.218.9Series 5
219.1 × 6.388.9 × 3.210.47.8Series 2
219.1 × 6.3114.3 × 3.611.48.6Series 2
219.1 × 6.3139.7 × 412.49.3Series 2
219.1 × 6.3168.3 × 4.512.99.7Series 2
219.1 × 6.3219.1 × 6.315.711.8Series 2
219.1 × 8219.1 × 819.414.5Series 4
219.1 × 12.5219.1 × 12.530.222.6Series 5
273 × 6.3114.3 × 3.610.98.2Series 2
273 × 6.3139.7 × 411.98.9Series 2
273 × 6.3168.3 × 4.512.89.6Series 2
273 × 6.3219.1 × 6.314.510.9Series 2
273 × 6.3273 × 6.316.312.2Series 2
323.9 × 7.1139.7 × 412.59.4Series 2
323.9 × 7.1168.3 × 4.513.410.1Series 2
323.9 × 7.1219.1 × 6.315.111.4Series 2
323.9 × 7.1273 × 6.316.912.7Series 2
323.9 × 7.1323.9 × 7.118.613.9Series 2
323.9 × 12.5323.9 × 12.531.323.5Series 5
355.6 × 8168.3 × 4.514.510.9Series 2
355.6 × 8323.9 × 7.119.314.5Series 2
355.6 × 8355.6 × 820.815.6Series 2
406.4 × 8.8219.1 × 6.316.912.7Series 2
406.4 × 8.8273 × 6.318.714Series 2
406.4 × 8.8406.4 × 8.823.617.7Series 2
457 × 10457 × 1026.820.1Series 2
508 × 11508 × 1129.522.2Series 3

standard dimension: D, D1 · standard value (not binding): Ts, Tb

Further deliverable dimensions (268)

Show full table · more than 200 rows
Further deliverable dimensions – 268 rows, from stock or to order, all dimensions in millimetres.
Doutside diameter, run in mmD1outside diameter, branch in mmTwall thickness, run in mmT1wall thickness, branch in mm
355.6219.15.64.5
355.6219.186.3
355.6219.1107.1
355.6219.112.58
355.6219.11612.5
355.6219.12016
355.6219.12817.5
355.6219.13622.2
355.62735.65
355.627386.3
355.6273108.8
355.627312.510
355.62731612.5
355.62732016
355.62732822.2
355.62733630
406.4168.36.34
406.4168.38.84.5
406.4168.3105.6
406.4168.312.57.1
406.4168.317.511
406.4168.322.214.2
406.4168.33017.5
406.4168.34022.2
406.4323.96.35.6
406.4323.98.87.1
406.4323.9108.8
406.4323.912.510
406.4323.917.512.5
406.4323.922.217.5
406.4323.93025
406.4323.94032
406.4355.66.35.6
406.4355.68.88
406.4355.61010
406.4355.612.512.5
406.4355.617.516
406.4355.622.220
406.4355.63028
406.4355.64036
457219.16.34.5
457219.1106.3
457219.1117.1
457219.112.58
457219.117.512.5
457219.122.216
457219.13217.5
457219.14522.2
4572736.35
457273106.3
457273118.8
45727312.510
45727317.512.5
45727322.216
4572733222.2
4572734530
457323.96.35.6
457323.9107.1
457323.9118.8
457323.912.510
457323.917.512.5
457323.922.217.5
457323.93225
457323.94532
457355.66.35.6
457355.6108
457355.61110
457355.612.512.5
457355.617.516
457355.622.220
457355.63228
457355.64536
457406.46.36.3
457406.4108.8
457406.41110
457406.412.512.5
457406.417.517.5
457406.422.222.2
457406.43230
457406.44540
508219.1106.3
508219.117.512.5
508219.12516
5082736.35
508273106.3
508273118.8
50827312.510
50827317.512.5
5082732516
5082733622.2
5082735030
508323.96.35.6
508323.9107.1
508323.9118.8
508323.912.510
508323.917.512.5
508323.92517.5
508323.93625
508323.95032
508355.61110
508355.612.512.5
5084576.36.3
5084571010
5084571111
50845712.512.5
50845717.517.5
5084572522.2
5084573632
5084575045
6102736.35
610273106.3
61027312.58.8
61027317.510
6102732512.5
6102733016
6102734522.2
6102736030
610323.96.35.6
610323.9107.1
610323.912.58.8
610323.917.510
610323.92512.5
610323.93017.5
610323.94525
610323.96032
610355.612.510
610355.617.512.5
610406.46.36.3
610406.4108.8
610406.412.510
610406.417.512.5
610406.42517.5
610406.43022.2
610406.44530
610406.46040
6104571010
61045712.511
61045717.512.5
6104572517.5
6104573022.2
6105086.36.3
6105081010
61050812.511
61050817.512.5
6105082517.5
6105083025
6105084536
6105086050
6106106.36.3
6106101010
61061012.512.5
61061017.517.5
6106102525
6106103030
6106104545
6106106060
711323.97.15.6
711323.9107.1
711323.912.58.8
711323.92510
711355.612.510
711355.62512.5
711406.47.16.3
711406.4108.8
711406.412.510
711406.42512.5
7114571010
71145712.511
7115087.16.3
7115081010
71150812.511
7115082512.5
7116107.16.3
7116101010
71161012.512.5
7116102517.5
7117117.17.1
7117111010
71171112.512.5
7117112525
813355.612.510
813355.62512.5
813406.486.3
813406.4108.8
813406.412.510
813406.42512.5
8134571010
81345712.511
81350886.3
8135081010
81350812.511
8135082512.5
81361086.3
8136101010
81361012.512.5
8136102517.5
81371187.1
8137111010
81371112.512.5
8137112525
81381388
8138131010
81381312.512.5
8138132525
914406.4106.3
914406.412.58.8
914406.42010
914406.42512.5
914508106.3
91450812.510
9145082011
9145082512.5
914610106.3
91461012.510
9146102012.5
9146102517.5
914711107.1
91471112.510
9147112012.5
9147112525
914813108
91481312.510
9148132012.5
9148132525
9149141010
91491412.512.5
9149142020
9149142525
1016610106.3
101661012.510
10166102012.5
10166102517.5
1016711107.1
101671112.510
10167112012.5
10167112525
1016813108
101681312.510
10168132012.5
10168132525
10169141010
101691412.512.5
10169142020
10169142525
101610161010
1016101612.512.5
101610162020
101610162525
1219711107.1
121971112.510
12197112012.5
12197112525
1219813108
121981312.510
12198132012.5
12198132525
12199141010
121991412.512.5
12199142020
12199142525
121910161010
1219101612.512.5
121910162020
121910162525
121912191010
1219121912.512.5
121912192020
121912192525

Order dimensions and values calculated by us; deliverable from stock or to order, availability on request. Limit deviations and figures from the standard: see the main table and the standard itself.

The dimensions given are nominal dimensions. The text of the standard prevails. The German edition DIN EN 10253-2:2026-07 reproduces the European version EN 10253-2:2021+A1:2025.

What has changed since the earlier edition

For the tee, the comparison covers the editions from DIN EN 10253-2:2008-09. Not yet recorded: DIN 2615:1964 and 2615-1/-2:1992.

DIN EN 10253-2:2008-09 → DIN EN 10253-2:2021-11

  • value

    The diameter 101.6 has been dropped from the tee table - in the cap and elbow tables the standard continues to carry it.

    Examples: ⌀ 101.6

    editions 2008-09 and 2021-11 · Table 13 against Annex A

DIN 2615-2:1992-05 → DIN EN 10253-2:2008-09

  • not yet recorded

    For this period the edition is not available to us - no comparison is claimed.

These entries say what the standard has changed. They say nothing about material, pressure rating, scope of testing or the condition of an installed part — and nothing about whether an existing part can continue to be used. That assessment remains with the specific plant.

Tees by dimension – ask our warehouse

You know the sizes of run and branch? Send us both outside diameters with their wall thicknesses, together with the material and the inspection document required. Our export team answers with price, availability and certificate.

Send an inquiry

Frequently asked questions

Where do I find the dimensions of a tee DN 100 to EN 10253-2?

The dimension table on this page lists all available sizes to EN 10253-2; the dimensional drawing above it shows the selected size with all dimensions and tolerances and can be printed as a PDF - the data sheet for your size.

Where is the wall thickness of a fitting measured – and does it apply in the bend?

At the welding end, as the full wall the way the standard enters T at the end plane – not at the root face and not across an inside taper (EN 10253-2 and -4, clauses 11.2.1 and 11.2.3). In the bend the wall may be thinner, but for type A fittings it must not fall below the lower limit for the welding ends. There is no upper limit on the body.

About this dimension table

All dimensions of the steel tee to EN 10253-2 (formerly DIN 2615) in one table, the dimensional drawing of your size above it – available from stock or to order. Butt-welding tees in steel are standardised in EN 10253-2. This page carries the figures: pick run, branch and wall thickness series, and the page shows the dimensional drawing, the dimension table and the limit deviations for exactly that size. For an equal tee, pick the same diameter for the branch as for the run. What the two centre-to-end dimensions F and G mean, and how type A differs from type B, is explained on the tee basics page.

The dimensional drawing – also called dimension sheet, outline drawing or dimension sketch – shows every dimension and the tolerances for your size.

Your inquiry to Zickwolff

Send us what you have – designation, standard, quantity, date. We will clarify the rest with you.

Related pages

← Back to the English knowledge hub

How this data is compiled. This page does not reproduce a standard. It shows the dimensions you need for an inquiry, an order and installation – for sizes we supply, checked against manufacturers’ and suppliers’ documentation and against our own product data. What you see here is what the market supplies, checked against the standard – or calculated by us. How we select our sources and keep them up to date: About this knowledge.

Technical basis: DIN EN 10253-2:2026-07 (butt-welding fittings of non-alloy and alloy steel), EN 10204. All information without guarantee – the current standard texts and the manufacturers’ technical data sheets always prevail.

We supply this material – availability, delivery options and inquiry on the supply page →

Ask the Wolf